No announcement yet.

ThruNite TN11S V2

  • Filter
  • Time
  • Show
Clear All
new posts

  • ThruNite TN11S V2

    Click image for larger version

Name:	7__28669.JPG
Views:	1
Size:	109.8 KB
ID:	299

    - Upgraded version of the TN11S with updated control system and updated LED.
    - Extra extension tubes to enable different batteries as a perfect duty light.
    - Outstanding momentary-on“forward clicky” tactical tail switch and improved side switch with one key to strobe access.
    - Stainless steel strike bezel for defense and emergency applications.
    - Wide working voltage enables CR123, rechargeable RCR123A and 18650 batteries.
    - Reversed polarity protection system prevents damage to the light.
    - Ultra clear tempered glass lens with anti-reflective coating.
    - Aircraft grade aluminum body structure with tactical knurling for firm grip.
    - Premium type III hard anodized anti-abrasive finish.
    - Memory function to set any mode(except for strobe) for immediate use.
    - Free holster, pocket clip and lanyard as a bonus.
    - LED: CREE XM-L2 U2 LED with a lifespan of 20+ years of run time.
    - Runs on: 1x18650 battery(LI-ION, 3200MAH).
    - Working Voltage: 3.3-12V.
    - Output mode/Runtime*: High(990 lumens / 110 minutes), Medium(208 lumens / 7 hrs), Low(5.2 lumens / 195 hrs).
    - Peak Beam Intensity: 29440cd.
    - Max beam distance: 343m.
    - Impact resistant: 2 meters.
    - Waterproof to IPX-8 Standard (1.5meters).
    - Weight: 168g without battery.
    - Dimensions: 163mm in length, 25.4mm in body diameter.41mm in head diameter.
    - Runs on: 2x 18650(LI-ION 3200MAH).
    - Working Voltage: 3.3-12V.
    - Output mode: High(1163 lumens), Medium(323 lumens), Low(16 lumens).
    - Runtime: Varies with different battery capacities.
    - Peak Beam Intensity: 33280cd.
    - Max beam distance: 365m.
    - Impact resistant: 2 meters..
    - Waterproof to IPX-8 Standard (1.5meters).
    - Weight: 204g without battery.
    - Dimensions: 227mm in length, 25.4mm in body diameter.
    Accessories: Extension Tubex2, Holsterx1, Pocket Clipx1, O ringx2, Lanyardx1.
    To turn on/off the light:
    Press the tail cap halfway to momentarily activate the light. Click the tail switch to turn the light on and off.
    To change modes:
    Four modes in total: low, medium, high, and strobe.
    When the light is on, single press the side switch to rotate among low, medium and high. Long press to get strobe and then single press to end it.
    One key to strobe: Press and hold the side switch to get strobe when the light is off. Long press to get strobe when the light is on. Hold strobe for three seconds to stay at it.
    Memory function: The light will turn on in the last mode accessed, except for strobe.
    Battery replacement:
    Take off the tail cap, insert the battery with positive polarity toward the LED assembly(head of the light), install the tail cap and tighten all the way to operate the light.
    With or without the extension tube, batteries filled in TN11S V2 can be 18650X1, 18650X2, CR123x1, CR123x2, CR123x3 and CR123x4.

    Warning: Do NOT use four rechargeable RCR123A batteries at a time for working voltage limit. And do NOT mix-use CR123 with 18650 batteries.

  • #2
    ... would there even be a plausible reason for a flashlight to take four RCR123 batteries in a series? That would take such a beefy buck driver for such a low overall capacity, it seems unreasonable. I mean, just look at what you can get with two 18650's already!


    • #3
      Editor Beetle

      For TN11s V2, it accepts 4*CR123, each at 3.0 volts which is within working voltage 12 volts.


      • #4

        No, no, the lithium primaries are fine, I know. They top off at 3V, so no worries.

        I mean the Li-Ion rechargeable ones that go up to 4.2V each. Four in series would reach 16.8V, a voltage I see no practical use for in an LED light.